6" and 12" SUPER-
ENGINEERING GRADE
REFLECTIVE TAPE

for FLAT SURFACES &
CYLINDRICAL SHAPES

Super Engineer Grade Reflective Tape Identi-Tape Logo
Facebook Icon

OTHER
WIDTHS:

--------------

1-inch
2-inch
4-inch


TYPE II SUPER-ENGINEERING GRADE (SEG) REFLECTIVE TAPE is for smooth flat surfaces & smooth cylindrical shapes (like a pipe - not for compound curves like a helmet).  SEG is 60% to 100% brighter than regular engineering grade reflective tape and is used for striping and lettering on fire trucks, EMS vehicles, pipe posts, bollards, barricades and signs.  It is not recommended for rough-finished wood.  We also offer white and blue in 12" width for vinyl-cutting machines to produce letters and numbers.  This reflective film is thin (5.5 mil) and utilizes embedded microscopic glass beadlets to reflect light.  It has a peel-off backing covering its permanent acrylic adhesive.  It is best applied using a soapy water solution (or Windex) and a squeegee.

Super-engineering grade tape is identified by a small (3/16") gray star watermark every 7" horizontally and every 2" vertically (example to left).  White, yellow, red, meet FHA specifications for highway signage; reflectivity (Type II), resistance to weathering, and longevity (12-year minimum), and exceed ASTM specifications D 4956 and LS-300C.  Tape should be applied when it and the surface to which it is applied to are both within the range of 64F to 77F, but it is service rated from -40ºF to 180ºF.  To maximize longevity, the adhesive should be allowed to cure 48 hours before being put into service.  The brightest reflecting color is white, followed by yellow, orange, red, and blue.  Tape is sold in 15-foot increments and 50-yd rolls.  Multiples of 15' lengths may be sent as a continuous length unless requested otherwise in the "comment box" when checking out.

NOTE:  for tape without "star" watermarks, or for surfaces that are irregular, like diamond plate on the backs of fire apparatus, or surfaces that involve compound curves, please see our Flexible Engineering Grade tapes in fluorescent yellow-green, red, white, and blue.
Super Engineer Grade Star
SEG has 3/16" gray
star water-marks
(shown on 1" tape)
Type II Super-Engineering Grade Reflective Tapes, 6-inch Width
for enhanced night time visibility
Approximate Color Color Sizes Price per
Length
Product
I.D.
View Cart
Reset Page
Add All to Cart
  White 6" x 15' $33.00 srse6w Qty:
6" x 150' $174.00
2 @ $165.30
3 @ $156.60
srseR6w Qty:
12" x 15'
for striping
and vinyl cutters
$58.00
now $38.00
srse12w Qty:
  Blue 12" x 15'
for striping
and vinyl cutters
$58.00
now $38.00
srse12bl Qty:
  Yellow
meets NFPA 1901
for fire apparatus
*
6" x 15' $33.00 srse6y Qty:
6" x 150' $174.00
2 @ $165.30
3 @ $156.60
srseR6y Qty:
  Orange 6" x 15' $33.00 srse6o Qty:
6" x 150' $174.00
2 @ $165.30
3 @ $156.60
srseR6o Qty:
  Red
meets NFPA 1901
for fire apparatus
*
6" x 15' $33.00 srse6r Qty:
6" x 150' $174.00
2 @ $165.30
3 @ $156.60
srseR6r Qty:
Return to Main Product Menu Top Arrow
Top
Facebook Icon
Add All to Cart
Reset Page
View Cart
Fire Apparatus Reflective Tape
Rollover to EnlargeFire Apparatus Tape
Back of EMS Vehicle with 6" Wide Stripes
*NFPA 1901:  Following are excerpts from the National Fire Protection Agency's 2009 NFPA 1901 Standard for Automotive Apparatus (fire trucks):

"15.9.3.2:  At least 50% of the rear vertical surfaces of the apparatus shall be equipped with a minimum 4 inch wide alternating yellow and red chevron retro-reflective striping sloping downward and away from the centerline of the vehicle at an angle of 45 degrees."

"15.9.3.3:  All retro-reflective material required by 15.9.3.1 and 15.9.3.2 shall conform to the requirements of ASTM D 4956, Standard Specification for Retro-reflective Sheeting for Traffic Control, Type I or better."